Ramsey-winch RPH 50000 UW/TNR & 2 SPEED MOTOR Manuel d'utilisateur

OPERATING, SERVICE AND MAINTENANCE MANUAL MODEL RPH-50,000 2 SPEED INDUSTRIAL PLANETARY WINCH CAUTION: READ AND UNDERSTAND THIS MANUAL BEFORE

7. Remove output coupling #8 and coupling shaft #6 from end bearing #10. Examine bearings #13 pressed in output coupling for signs of wear. Replace

RE-ASSEMBLY 9. NOTE: DETERMINE MOUNTING CONFIGURATION OF WINCH ( “A” ROTATION DRIVER SIDE OR “B” ROTATION PASSENGER SIDE) BEFORE RE-ASSEMBLY OF WIN

10. Gently tap key #5 into keyway of input shaft #11. Liberally apply grease to shoulder of input shaft. Place 1-3/4 OD washer #28 over end of shaft

11. Seat well-oiled quad-ring #41 into groove of bushing in each end of drum assembly #1. Carefully set drum assembly down onto motor end bearing #9.

12. If removed, install bushing #14 into gear housing #10. Press bushings #30 into each end of output coupling #8. Place end (with longest splines) o

Set gasket #36 into place on gear housing end bearing #10. Place ring gear #49 onto end bearing, aligning holes in ring gear with holes in gasket an

14. Apply Loc-tite to threads of nut #27 and thread onto setscrew #21 to 3/8 inch from drive end, as shown below. Slide washer #26 over set screw u

16. Apply thread sealer to threads of plug #43. Thread plug into tapped hole in bottom of gear end bearing #10. Pour approximately 2.5 quarts of S

16 P/N 123628 "B" ROTATIONPASSENGER SIDEP/N 123627 "A" ROTATIONDRIVER SIDE WINCH MOUNTING CONFIGURATIONS

17

TABLE OF CONTENTS INTRODUCTION ... 1 WARRANTY

18

19

395448 (234156) DRUMDRUM ASSEMBLY1a1c1f1b1g1f1d1e395448 (234240) DRUM20

50g50k50b50f50c50e50a50d50i50j50h50p50m50q50n50s50rPARTS LIST FOR TENSIONER (256139) ITEM QTY. PART # DESCRIPTION 50a 2 330015 DRAG PUCK 5

123627 & 12362811954144451028431412213LONGEST SPLINES27813273642638412924354616191935e35d35e184720403235a3335c1635b20748364492339122127371526343

ITEM QTY. PART # DESCRIPTION ITEM QTY. PART # DESCRIPTION 1 1 395448 DRUM ASSEMBLY, CABLE ANCHOR M.E. (123628) 29 4 418453 SHOULDER BOLT

TENSIONER KIT INSTALLATION CABLE IN ROTATION1/4 NPT PORT(125 PSI) MAXNOTE: ACTUATORSPRING ENGAGEDAIR RELEASENOTE:INSTALL DRAG BRAKE PER DRAWING.AD

25

LIMITED WARRANTY RAMSEY WINCH warrants each new RAMSEY WINCH to be free from defects in material and workmanship for a period of one (1) year f

file:///L:/Owners%20manuals/Current/Manual%20Index_files/sheet001.htmIndustrial WinchesRPH 50000 UW/TNR & 2 SPEED MOTOR914242 B123627 123628file:

RAMSEY HYDRAULIC PLANETARY WINCH MODEL RPH 50,000 PLEASE READ THIS MANUAL CAREFULLY This manual contains useful ideas in obtaining the most efficien

WINCH MOUNTING Use (8) 3/4" diameter grade 5 or better bolts to attach winch to the wrecker. Before operating the winch for the first time, remo

PERFORMANCE CHARTS (BASED ON 9.6 CU. IN./REV MOTOR-LOW SPEED) CLUTCH OPERATION To engage clutch: 1. Move the clutch control valve

4 MAINTENANCE Adhering to the following maintenance schedule will keep your winch in top condition and performing as it should with a minimum of rep

INSTRUCTIONS FOR OVERHAUL DIS-ASSEMBLY 1. Drain oil from gear housing #10 by removing pipe plug #43 from in end bearing. Remove reducer #42 and reli

19161635c3335a35e35d35e19973. Remove brake assembly screws #16 from brake 35a to access (2) mounting screws #19 attaching brake adapter plate #35d

5. Pull drum assembly #1 upward from end bearing #10. Remove quad-rings #41 from grooves in drum bushings. Remove input shaft #11, clutch springs #4