Ramsey-winch CABLE TENSIONER 800/H-800 256107 Manuel d'utilisateur télécharger pdf

INSTALLATION INSTRUCTIONS FOR KIT #256107

CABLE TENSIONERS FOR 800/H-800 SERIES WINCHES

This tensioner kit is designed specifically for Ramsey Winch Model 800/H-800 series winches. Kit #256107

is for both underwound and overwound winches.

INSTALLATION PROCEDURE

Disengage the winch clutch and freespool all the cable except for the last wrap off the winch. Lay cable out

in a straight line behind the truck to prevent kinking. Mark mounting hole centers as shown on the following

page. Place cable tensioner assembly over marked hole positions, orienting it correctly for either an

overwound or underwound winch (see following page). Observe location of tensioner plate and center it

between the drum flanges. Adjust hole locations as necessary to maintain centered position. Drill two .562

diameter holes through the rear angle as shown on the following page.

Place the supplied mounting bolts through the mounting holes of the tensioner bracket. Position the bracket

over the previously drilled holes in the rear angle, allowing the bolts to fall through the holes. Loosely attach

the washers and nuts.

Center the tensioner plate between the drum flanges with a scale or tape measure and tighten the bolts

securely (87 ft-lbs. of torque).

If you removed the cable entirely, or this is a new installation, the cable tensioner is not intended to be

energized on a bare drum. Before increasing the tension on the cable tensioner, engage the clutch and run

the winch in the reel in direction winding one full wrap of cable on the drum. This prevents damage to the

cable tensioner.

Engage the clutch and run the winch in the reel in direction, winding about five wraps of cable onto the

drum and stop. Using a hammer, tap these five wraps tightly against the side of the flange closest to the

cable anchor on the cable drum. Finish winding all the cable onto the cable drum. As cable winds onto the

drum, watch the tensioner. Tensioner must be free to move without obstruction to function properly. If

tensioner touches any surrounding structure, correct the problem.

To adjust the freespool effort of the tensioner, turn the adjustment nut at the top or bottom of the tensioner

assembly (see drawing on following page). This will adjust the spring height. Start adjusting the tensioner

with the spring height at 5.50”. Disengage the winch clutch and freespool some cable off the drum. Adjust

the spring tension to achieve the desired freespool effort that also prevents “bird nesting” of the cable.

OPERATION

Once you have adjusted the spring tension to the desired level, only minor adjustments may be required if

the setting drifts.

KI-912592-1205-D

RAMSEY WINCH COMPANY

P.O. BOX 581510

TULSA OK 74158-1510

www.ramsey.com

1 2

Résumé du contenu

Page 1 - OPERATION

INSTALLATION INSTRUCTIONS FOR KIT #256107 CABLE TENSIONERS FOR 800/H-800 SERIES WINCHES This tensioner kit is designed specifically for Ramsey Winch M

Page 2 - Cable feeds out

2 UNDERWOUND INSTALLATION OVERWOUND INSTALLATION (REF)2.0050,811.62295,13.5389,6TENSIONER REQUIRES TWO Ø.562 (14,3mm)HOLES IN WINCH MOUNTING ANGL

Commentaires sur ces manuels

Pas de commentaire

Ramsey-winch CABLE TENSIONER 800/H-800 256107 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Ramsey-winch CABLE TENSIONER 800/H-800 256107. Ramsey Winch CABLE TENSIONER 800/H-800 256107 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Ramsey-winch CABLE TENSIONER 800/H-800 256107