Ramsey-winch LEVEL WINDER 1 256048 Manuel d'utilisateur télécharger pdf

1 KI-912513-0204-G

INSTALLATION INSTRUCTIONS

FOR MODEL 1 LEVEL WINDER KIT

#256048

This Level Winder is designed specifically for the Ramsey Winch Models 200/300 Series Winches

(200/300, H200/H300 or DC200/DC300), which is 11.31 inches between drum flanges. It will also work

on Braden Winch Co. Model U8, Tulsa Winch Co. Model H938, Desert Dynamics Model 1106-11, 1306-

11, 1106-11H or Pierce Model DC11R, which have the 11.31 inches long cable drum.

NOTE:

IF LEVEL WINDER IS BEING INSTALLED ON A CAR CARRIER (ROLLBACK), IT IS

NECESSARY TO ALSO INSTALL RAMSEY ROLLER GUIDE KIT, PART NO. 256049. FAILURE TO

DO SO MAY CAUSE DAMAGE OR BREAKAGE TO THE WINCH LEVEL WINDER OR VEHICLE.

INSTALLATION PROCEDURE

Disengage the winch clutch and free spool all the cable off the winch and lay it in a line on the ground

behind the truck. Disconnect the end of the cable from the cable drum anchor. Drill .531” diameter holes

through the horizontal flange of the forward-most winch mounting angle as shown in FIG. 1.

Insert the spring retainer into the springs so that the cleat at the center of the retainer will extend toward

the vehicle cab when the assembly is in place. Slide the retainer into the spring so that the hole in the

center of the retainer lines up with the hold-down loop in the center of the spring. Position the hole in the

center of the retainer over the .531” diameter hole previously drilled in the flange of the winch mounting

angle. Loosely attach the spring retainer and spring to the flange of the winch mounting angle using the

1/2 inch diameter capscrew, nut and lockwasher.

After making sure the spring and spring retainer are aligned squarely with the winch, as shown in FIG. 2,

install the other capscrew, nut, and lockwasher into the other hole and tighten both capscrews securely

so that the spring is clamped hard down onto the mounting surface.

NOTE: The surface to which the spring is bolted must be 2.00 ± .50 inch above the centerline of

winch mounting bolts. See FIG. 2, VIEW A-A.

Insert the end of the cable into the opening of the tensioner so that it passes under the center cross bar

and over the front cross bar and install the cable into the cable anchor. Make a sharp bend in the cable

where it comes out of the cable anchor. Bring the tensioner up to the winch and lift up first one then the

other of the spring tangs while sliding the center cross bar of the tensioner under the tangs. A pry bar will

DRUM

200/300

WINCH MOUNTING

ANGLE

VEHICLE CAB

DRUM

FIGURE 1

SERIES WINCH

DRILL .531 (17/32) DIA.

THRU. (2 PLACES)

1 2

Résumé du contenu

Page 1 - #256048

1 KI-912513-0204-G INSTALLATION INSTRUCTIONS FOR MODEL 1 LEVEL WINDER KIT #256048 This Level Winder is designed specifically for the Ramsey Winch Mod

Page 2 - FIGURE 2

2 KI-912513-0204-G be necessary to lift up the tangs. Push the tensioner toward the spring until the half loops at the end of each spring tang snap i

Commentaires sur ces manuels

Pas de commentaire

Ramsey-winch LEVEL WINDER 1 256048 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Ramsey-winch LEVEL WINDER 1 256048. Ramsey Winch LEVEL WINDER 1 256048 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Ramsey-winch LEVEL WINDER 1 256048